Heat transfer and hybrid ferrofluid flow over a nonlinearly stretchable rotating disk under the influence of an alternating magnetic field

Scientific Reports volume 12, Article number: 17548 (2022) Cite this article

1145 Accesses

7 Citations

Metrics details

Under the influence of an alternating magnetic field, flow and heat transfer of a ferrofluid flow over a flexible revolving disc are examined. The flow is hampered by the external magnetic field, which is dependent on the alternating magnetic field's frequency. The current work examines the heat transfer and three-dimensional flow of fluid with high viscosity on a spinning disc that is stretched in a radial direction. The governing equations' symmetries are computed using Lie group theory. In the problem, there is a resemblance that can accomplish with radially stretching velocities divided into two categories, specifically, linear and power-law, by imposing limits from the boundary conditions. The literature has already covered linear stretching, but this is the first discussion of power-law stretching. The governing partial differential is turned into an ordinary differential equations system using additional similarity transformations, which are then numerically handled. The results are presented for hybrid alumina–copper/ethylene glycol (\({\text{Al}}_{2} {\text{O}}_{3} - {\text{Cu}}/{\text{EG}}\)) nanofluid. The calculated findings are novel, and it has been seen that they accord quite well with those of the earlier extended literature. It has been found that hybrid nanofluid flow outperforms nanofluid flow in terms of Nusselt number or heat transfer rate. The heat transmission in the fluid is reduced as the Prandtl number is increased. The heat transfer increases as dimensionless magnetic field intensity \(\xi\) increases. Also, axial velocity and radial velocity decrease as magnetic field intensity increases. As the ferromagnetic interaction parameter is raised, the efficiency of heat transmission decreased. For non-linear stretching with stretching parameter 0 < m < 1, the velocity decreases with the increase in m.

Numerous applications of the study of the flow field caused by a revolving disc have been identified in numerous technical and industrial domains. Fans, turbines, centrifugal pumps, rotors, viscometers, spinning disc reactors, and other rotating bodies are only a few examples of real-world applications for disc rotation. The study of an incompressible viscous fluid across an infinite plane disc rotating with a uniform rotational velocity was first introduced in the renowned article by Von Karman1, which established the history of rotating disc flows. Numerous researchers are continuing to look at this model to produce analytical and numerical results for a better understanding of the fluid behaviour caused by rotating discs. Von Karman1 first proposed the use of similarity transformations to change the governing Navier Stokes equations for axisymmetric flow into a set of linked nonlinear ordinary differential equations, and Cochran2 then reported the numerical findings for these equations. The effects of heat transport over a revolving disc at a constant temperature were examined by Millsaps and Pohlhausen3. For large Prandtl numbers, Awad4 provided an asymptotic model to investigate the heat transport phenomena over a spinning disc. The flow caused by stretched surfaces finds significant use in the manufacturing sector, particularly in the extrusion of metals and polymers5,6,7. Crane8 provided the precise analytic solution for the steady linear stretching of a surface. This issue was expanded to include three dimensions by Wang9. Using the Homotopy Analysis Method, Rashidi and Pour10 discovered approximative analytical solutions for the flow and heat transmission over a stretched sheet. Fang11 was the first to suggest the steady flow over spinning and stretching disk. Recent research on the flow between two extending discs was conducted by Fang and Zhang12. More recently, Turkyilmazoglu13 examined the combined effects of magnetohydrodynamics on radially stretched discs. We note that the linear radial stretching velocities were the focus of all of this research. Stretching of the sheet may not always be linear in practical circumstances, according to Gupta and Gupta14.

By incorporating nanoparticles into the carrier liquid, heat transfer coefficients can be improved15. CuO nanofluid with water and ethylene boiling properties have been investigated16. For heat transfer applications, the nanofluid's liquid medium is crucial17. For nanofluid flow boiling heat transfer, a novel model has been devised18. A growing proportion of nanotechnology for heat transmission is called nanofluids, which are colloidal mixtures of nanoparticles (1–100 nm) and base liquid (nanoparticle fluid suspensions). Nanofluids' heat transfer capabilities have been investigated to use them as a coolant19. The analysis of heat transmission has been done on multi-wall nanotube nanofluids20. Some recent work on nanofluid flow can be seen in21,22. A spinning disc created viscous fluid flow, which has been explored by Cochran2. Similar issues have been investigated by Benton using recurrence relation approaches23. These sorts of difficulties have been expanded for magnetohydrodynamic flow due to their employment in a spinning system13,24,25,26. Due to the technical uses of ferrofluid in a revolving system, research investigation on ferrohydrodynamic flow caused by a spinning disc was carried out. An analytical solution was used to investigate the influence of the viscosity of ferrofluid flow affected by the magnetic field owing to a spinning disc27. For ferrohydrodynamic flow in a revolving system, heat transfer analysis and mathematical modeling have been published28. It looked at how magnetic field-dependent viscosity affected ferrofluid flow that isn't consistent over a spinning disc29.

Magnetic nanoparticles are suspended colloidally in a carrier liquid to form ferrofluids. To make ferrofluid, at least three ingredients are necessary: carrier liquid, nano-sized magnetic particles, and surfactants. Ferrofluids are primarily employed in the hard disc drive sealing process. Ferrofluids are employed as a lubricant in rotating shafts in a variety of commercial equipment. It's also utilized in speaker coils to boost the acoustic output of the speakers. In the therapy and diagnosis of cancer, ferrofluids play a critical role. A solar collector's thermal performance with displaced pipes may be measured via ferrofluids30. When there is an alternating magnetic field present, the viscosity of significance of magnetic fluid is crucial in optimizing the technical use of ferrofluid. The researchers looked at the viscous behavior of ferrofluid in the existence of a fixed magnetic field31,32,33,34. The viscosity of magnetic fluid changes as it is visible to an alternating magnetic field35,36,37,38. Between contracting spinning discs, the rheological properties of metal-based nanofluids have been investigated39. The study of magnetic viscosity is affected by the magnetic field necessitates the use of an external magnetic field. The magnetic torque and magnetization force are highly significant to examine the flow properties of fluid with magnetic properties in many forms of ferrofluid flow40,41,42,43. Especially in electrical engineering and electromechanics, magnetic fields are utilised in all areas of contemporary technology. Power generators and electric motors both employ rotating magnetic fields. The study of the entropy formation model's mathematical justification has been provided, along with magnetoviscous effects on ferrofluid flow in the presence of an alternating magnetic field44. Analysis of entropy generation and thin-film Maxwell fluid flow across a stretchable spinning disc have been studied45,46. The effects of nonlinear thermal radiation on a hybrid nanofluid across a cylindrical disc have been studied47. The binary diffusion theory was used to investigate the rotational flow of Oldroyd-B nanofluid48. The effect of the Hall current has been used to conduct a hybrid nanofluid over a revolving disc49. To improve the viscosity and thermal conductivity of the nanofluid, silver nanoparticles were utilized50. Considering a transverse magnetic field, nanofluid flow behavior and heat transfer across a porous shrinking surface were investigated51. The flow of nanofluid across a cylindrical disc in a non-axisymmetric stagnation point has been studied52. When a static magnetic field is present, the properties of magnetic body force and rotational viscosity in ferrofluid flow across a stretched sheet were investigated53. Maxwell nanofluid flow across a spinning disc with a chemical reaction was investigated54. The properties of heat mass transport processes have been examined using thin film deposition of nanofluid over an uneven stretched surface55. When there is a constant magnetic field present, the heat transfer properties of a water-based \({\text{Fe}}_{3} {\text{O}}_{4}\) nanofluid have been examined56.

The convective heat transfer of a magnetite-water nanofluid in the presence of an external magnetic field was experimentally examined by Azizian et al.57. The scientists found that as the magnetic field strength and Reynolds number rise, so do the heat transfer and pressure decrease. Goharkhan et al.58 carried out experimental research on the convective heat transfer of \({\text{Fe}}_{3} {\text{O}}_{4}\)-water nanofluid within a heated tube in the presence of continuous and alternating magnetic fields. When the Reynolds number and nanoparticle concentration rise, an increase in heat transmission is seen. Additionally, it was discovered that when the magnetic field's intensity rises, the temperature at the walls' surface falls. Particularly, the temperature decrease is greater when an alternating magnetic field rather than a steady magnetic field is applied. The impact of a non-uniform magnetic field on convective heat transport in a Fe3O4-water ferrofluid was investigated by Sheikholeslami and Ganji59. Both magnetohydrodynamic and ferrohydrodynamic effects are taken into account in their analysis, and the magnetic field is created by a current-carrying wire. When the Rayleigh number, nanoparticle volume fraction, and magnetic number are increased, an increase in heat transfer is seen. Heat transfer is reduced though as the Hartmann number rises. In the presence of a non-uniform magnetic field, Gibanov et al.60 looked at the convective flow of water-based magnetite ferrofluid in a lid-driven cavity with a heat-conducting solid backward step. In their experiment, a magnetic wire is positioned above the top wall of the cavity and produces a non-uniform magnetic field. The intensity of convective circulation and heat transfer is found to increase as the magnetic number rises, according to the authors. The rate of heat transfer increases along with the volume fraction of nanoparticles. However, a higher Hartmann number results in a slower rate of heat transfer and fluid flow. Ghasemian et al.61 carried out a two-phase numerical study on the forced convective heat transfer of magnetite water-ferrofluid through a mini-channel while being affected by constant and alternating magnetic fields. The constant magnetic field is produced by current-carrying wires that are positioned below the channel, whereas the alternating magnetic field is generated by imposing rectangular wave functions on the current source of current-carrying wires, which are located above and below the channel. When the magnetic field is constant, increasing its intensity causes the flow velocity to rise over the top surface of the channel and lowers the temperature of the ferrofluid. The fluid's velocity changes along the channel's width when an alternating magnetic field is provided, which improves heat transmission. Additionally, compared to a steady magnetic field, an alternating magnetic field improves heat transmission. It was also discovered that there is a magnetic field frequency value that, as the Reynolds number rises, maximises the heat transfer improvement. Some recent work can be seen in62,63,64,65.

A systematic approach called lie group analysis is used to find the invariant or self-similar set of partial differential equations solutions. The technique provides a profound understanding of the physical issues that are described by partial differential equations. Lie group analysis has two applications: producing a new solution from an existing solution and discovering similar solutions for partial differential equations. The current study concentrates on the latter sort of application. This approach, which dates back to the Sophus Lie (1842–1899), is often employed to solve differential equations66,67,68. This approach was used by Jalil et al.69 to discover suitable similarity transformations for mixed convection flow across a stretched surface. They expanded their work to non-Newtonian fluid flow70,71 by utilizing Lie group analysis to identify self-similar solutions to the governing equations. Hamad et al.72 used Lie group analysis to explore the combined impacts of heat and mass transmission across a moving surface. Ferdows et al.73 investigated mixed convection over a horizontal sliding porous flat plate using the one-parameter continuous group theory approach. Ferdows et al.74 studied the convective effects of heat and mass transmission across a radiating stretched sheet using a specific type of Lie group of transformation (scaling transformation).

Some of the distinct attributes of nanofluid and ferrofluid have been researched in the preceding literature review. Researchers have explored the rotating flow of a nanofluid in the presence of various physical factors.

When there's a variety of physical challenges, the rotating nanofluid flow has been investigated. In this current work, under the effects of an alternating magnetic field, hybrid nanofluid flow and heat transfer over a non-linear stretchable rotating disc are studied. The frequency of the alternating magnetic field determines how much the external magnetic field impedes the flow. We considered this problem with two different nanoparticles (\({\text{Al}}_{2} {\text{O}}_{3}\)–Cu) suspended in the base fluid ethylene glycol (EG). In the current physical model, the theoretical formula for rotating viscosity in the presence of an alternating magnetic field are adopted. The current model is transformed into a dimensionless form using a similarity transformation. The BVP4c is used to solve a set of nonlinear-coupled differential equations using MATLAB software. For various values of the physical parameters utilized in the problem, the findings for radial velocity, tangential velocity, axial velocity, and temperature distributions are reported.

Figure 1 depicts the flow arrangement. In the presence of an alternating magnetic field, the flow of a \({\text{Al}}_{2} {\text{O}}_{3} - C_{u} /EG\) ferrofluid over a radially extending disc is examined. The disc rotates at a constant angular velocity \(\omega\) around the z-axis. Let the temperature on the disk's surface is \(T_{w}\) and \(T_{c}\) is the temperature of Curie. The flow is deemed axisymmetric and incompressible. The constitutive equations for the motion of ferromagnetic nanofluids, magnetization equation, energy equation, and Maxwell equations are as follow20,29:

Flow across an extending disc is depicted.

\((\mu_{0} = 4\pi \times 10^{ - 7} Henery/meter)\) is the magnetic permeability of the free space of the nanofluid. In comparison to a relaxation term, \(\frac{{d\omega_{p} }}{dt} \ll \frac{{I\omega_{p} }}{{\tau_{s} }}\) the inertial expression is negligible. Therefore, Eq. (3) can be reduced as:

Equations (1) and (2) can be expressed as follow by using Eq. (7):

In the radial direction, the alternating magnetic field is applied as follows75:

where the applied magnetic field's angular frequency is \(\omega_{0}\), \(H_{0}\) signifies the magnetic field's amplitude. Consider Eq. (10) as a principle of superposition of two spinning fields: the left-hand polarized field (subscript +) and the right-hand polarized (−), then:

Assume that the magnetization lags after the magnetic field at a certain angle \(\alpha_{0}\). Then

Using Eqs. (3), (4), (11) and (12) we get:

The magnetic energy to thermal energy \(\left( {\xi = \frac{{mH_{0} }}{kT\sqrt 2 }} \right)\) ratio is quite tiny, and using the expression \(I = 6\mu \tau_{s} \varphi\). Eliminating the angle \(\alpha_{0}\) from Eq. (13):

\(\frac{{H_{0} }}{\sqrt 2 }\) is the root mean square value of the \(H_{0} \cos \omega_{0} t\) and \(\alpha_{0}\) is the magnetic field's phase angle with the magnetization. Taking into account the hydrodynamical vortex \(\Omega = \left( {0,0,\Omega } \right)\) and the spinning magnetic field, magnetization's tangential components are as follow75:

The tangential component of magnetization is: if the field becomes linearly polarized along the radial direction

Along the z-axis, the magnetic torque operates on the fluid as follows75:

Taking the average of Eq. (19) throughout the field fluctuation period \(\frac{2\pi }{{\omega_{0} }}\),

Because of the oscillating magnetic field, the expression \(\frac{1}{4}\varphi \xi^{2} \left( {\frac{{1 - \omega_{0}^{2} \tau_{B}^{2} }}{{\left( {1 + \omega_{0}^{2} \tau_{B}^{2} } \right)^{2} }}} \right)\) is termed rotating viscosity. It is determined by the magnetic field's strength \(\xi\) as well as the magnetic field's frequency. For \(\omega_{0} \tau_{B} > 1\), the rotating viscosity decreases. This is referred to as a negative viscosity impact. If \(\omega_{0} \tau_{B} = 1\), the rotating viscosity does not influence the fluid. If \(\omega_{0} \tau_{B} < 1\), the fluid is subjected to increased resistance due to the oscillating magnetic field. In the limiting case \(\omega_{0} \tau_{B} \to \infty\), the impact of rotating viscosity vanishes due to the nanoparticles in the fluid no longer sensing the magnetic field.

The applied magnetic field has a scalar potential75

The magnetic field components in radial and tangential directions can be written as75

The intensity of the entire magnetic field can be calculated as follows75

In the radial and tangential directions, the following are the rates of change in magnetic field intensity75

The radial and tangential magnetization forces can be represented as follows75

The temperature has a linear effect on magnetization, as follows75

In the above equation, the pyro magnetic coefficient is denoted by \(K^{a}\) and the Curie temperature is denoted by \(T_{c}\). Equations (2), (5), and (8) can be written in cylindrical form using Eqs. (20, 25), and (26):

Incorporating non-dimensional variables into the governing Eqs. (27)–(32) is a practical way to find boundary layer equations. For the current problem, we examine the following non-dimensional variables:

where \({\text{Re}} = \frac{{\Omega R^{2} }}{\upsilon }\) is Reynolds number, the reference length is designated by \(R\) and the reference temperature is \(\left( {T_{w} - T_{\infty } } \right)\). It's worth noting that in the axial direction, the analogous scales are smaller by a factor \({\text{Re}}^{{{{ - 1} \mathord{\left/ {\vphantom {{ - 1} 2}} \right. \kern-\nulldelimiterspace} 2}}} ,\) As a result, \({\text{Re}} \gg 1\) is implicitly foreshadowed. The controlling Eqs. (27)–(32) are now transformed into a dimensionless version, as follows:

where Prandtl number is \(\Pr = {\upsilon \mathord{\left/ {\vphantom {\upsilon {\alpha_{T} }}} \right. \kern-\nulldelimiterspace} {\alpha_{T} }}\).

When the Reynolds number is high, i.e., \({\text{Re}} \to \infty\), In dimensionless form, the resultant boundary layer equations are as follows:

The following are the ferrofluid flow boundary conditions across a stretched disc:

Von Karman1 suggested the similarity transformation, which has the characteristic that pressure depends only on z. According to Eq. (42), the pressure in the axial direction is constant in the boundary layer area. The logical conclusion from this is that the pressure term within the boundary layer is simply constant and, as a result, identical to the ambient pressure.

Density \(\left( {\rho_{nf} } \right)\), viscosity \(\left( {\mu_{nf} } \right)\) and thermal diffusivity \(\left( {\alpha_{nf} } \right)\) of nanofluid are75,

The thermophysical properties \(\rho_{hnf}\), \(\left( {\rho c_{p} } \right)_{hnf}\), \(\mu_{hnf}\) and \(k_{hnf}\) are defined for hybrid nanofluid (Al2O3-Cu/EG) are defined as76,

where

Using base fluid, Table 1 shows the physical characteristics of the carrier liquid and nanoparticles.

Using the following similarity transformation,

The continuity Eq. (39) is immediately met by using the similarity transformation (47), and the boundary layer issue (40)–(43) is readily translated into a self-similar form:

The following are the boundary conditions:

The dimensionless quantities are used as follows:

the ferromagnetic interaction numbers are \(\beta ,\beta_{1} ,\beta_{2}\) and \(\beta_{3}\), Prandtl number is denoted by Pr, the thermal diffusivity is \(\alpha_{f} = \frac{k}{{\rho c_{p} }}\) in Eq. (52). The parameter \(\alpha\) is the disc stretching parameter, which is a constant. The shear stress on the disk's surface \(\left( {\tau_{s} } \right)\), wall \(\left( {\tau_{w} } \right)\) and flow of heat from the walls can be computed as follows:

For different values of volume concentration \(\left( \varphi \right)\), dimensionless magnetic field intensity \(\left( \xi \right)\), dimensionless frequency \(\left( {\omega_{0} \tau_{B} } \right)\), Prandtl number \(\left( {Pr} \right)\) and ferromagnetic interaction numbers \(\left( {\beta ,\beta_{1} ,\beta_{2} ,\beta_{3} } \right)\), a graphical result for axial velocity \(\left( f \right)\), radial velocity \(\left( {f^{\prime}} \right)\), tangential velocity (g) and temperature \(\left( \theta \right)\) has been presented in this work. The BVP4c method in the MATLAB programmer is used to achieve the numerical solution of nonlinear coupled differential equations. The current numerical work is confirmed with prior work after reducing specific physical factors. The dimensionless ferromagnetic interaction numbers \(\left( {\beta ,\beta_{1} ,\beta_{2} ,\beta_{3} } \right)\) determine the different types of velocities such as axial velocity, tangential velocity, and radial velocity, as well as temperature distribution. Ethylene glycol is used as the basic fluid in this experiment. The nanoparticles of alumina \({\rm Al}_{2}{\rm O}_{3}\) and Cu are utilized in the preparation. To keep the nanoparticles from clumping together in the transported liquid, ferrofluid was utilized. Table 1 lists the thermophysical characteristics taken into account in this physical model. Figure 2 shows that the axial velocity due to fluctuation of ferromagnetic interaction numbers \(\beta\). The current figure physically shows that the fluid becomes more viscous with rising values of \(\beta\), which causes the fluid's velocities to decrease. Figures 3, 4, 5 represents the temperature profile for different values of ferromagnetic dimensionless interaction numbers. In this case when increasing the value of ferromagnetic interaction numbers then decrease the temperature profile in the flow field. Figures 6, 7, 8, 9 illustrate that the axial velocity, tangential velocity, temperature profile and radial velocity decrease when increasing the value of dimensionless parameters \(m\).

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(\beta\) with R = 3, n = 3, v = 0.3, \(\phi\) = 0.3, Pr = 0.6, \(\phi_{1}\) = 0.1, \(\phi_{2}\) = 0.8, m = 1.5, \(\beta_{1}\) = 0.2, \(\beta_{2}\) = 0.5, \(\beta_{3}\) = 0.5, u = 0.2, \(\xi\) = 0.2.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(\beta_{1} \left( \eta \right)\) with R = 3, n = 3, v = 0.3, \(\phi\) = 0.3, Pr = 0.6, \(\phi_{1}\) = 0.1, \(\phi_{2}\) = 0.8, m = 1.5, \(\beta\) = 0.4, \(\beta_{2}\) = 0.5, \(\beta_{3}\) = 0.5, u = 0.2, \(\xi\) = 0.2.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(\beta_{2} \left( \eta \right)\) with R = 3, n = 3, v = 0.7, \(\phi\) = 0.3, Pr = 0.6, \(\phi_{1}\) = 0.1, \(\phi_{2}\) = 0.8, m = 1.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{3}\) = 0.5, u = 0.2, \(\xi\) = 0.2.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(\beta_{3} \left( \eta \right)\) with R = 3, n = 3, v = 0.7, \(\phi\) = 0.3, Pr = 0.6, \(\phi_{1}\) = 0.1, \(\phi_{2}\) = 0.8, m = 1.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(m\) with R = 3, n = 3, v = 0.1, \(\phi\) = 0.2, Pr = 0.6, \(\phi_{1}\) = 0.4, \(\phi_{2}\) = 0.8, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(m\) with R = 3, n = 3, v = 0.1, \(\phi\) = 0.2, Pr = 0.6, \(\phi_{1}\) = 0.4, \(\phi_{2}\) = 0.8, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(m\) with R = 3, n = 3, v = 0.1, \(\phi\) = 0.2, Pr = 0.6, \(\phi_{1}\) = 0.4, \(\phi_{2}\) = 0.8, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Representation of tangential velocity \(g\left( \eta \right)\) for the different values of \(m\) with R = 3, n = 3, v = 0.1, \(\phi\) = 0.2, Pr = 0.6, \(\phi_{1}\) = 0.4, \(\phi_{2}\) = 0.8, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Figures 10, 11, 12, 13 demonstrated the distributions of axial velocity, radial velocity, tangential velocity and temperature profile for distinct values of \(\phi\). In this case when \(\phi = 0\) then the flow of carried liquids only. If we increase the value of \(\phi\) the axial and radial velocity are increased and tangential velocity and temperature are decreased. Volume concentration profile creates the resistance in the flow field, in the existence of magnetic field. The heat transmission in the fluid is improved when the carrier liquid has a greater volume concentration.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(\phi\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.7, \(\phi_{1}\) = 0.2, \(\phi_{2}\) = 0.4, \(\beta_{3}\) = 0.6, \(\beta\) = 0.4, \(\beta_{1}\) = 0.3, \(\beta_{2}\) = 0.5, u = 0.4, \(\xi\) = 0.4.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(\phi\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.7, \(\phi_{1}\) = 0.2, \(\phi_{2}\) = 0.4, \(\beta_{3}\) = 0.6, \(\beta\) = 0.4, \(\beta_{1}\) = 0.3, \(\beta_{2}\) = 0.5, u = 0.4, \(\xi\) = 0.4.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(\phi\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.7, \(\phi_{1}\) = 0.2, \(\phi_{2}\) = 0.4, \(\beta_{3}\) = 0.6, \(\beta\) = 0.4, \(\beta_{1}\) = 0.3, \(\beta_{2}\) = 0.5, u = 0.4, \(\xi\) = 0.4.

Representation of tangential velocity \(g\left( \eta \right)\) for the different values of \(\phi\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.7, \(\phi_{1}\) = 0.2, \(\phi_{2}\) = 0.4, \(\beta_{3}\) = 0.6, \(\beta\) = 0.4, \(\beta_{1}\) = 0.3, \(\beta_{2}\) = 0.5, u = 0.4, \(\xi\) = 0.4.

In similar manners to Figs. 14, 15, 16, 17, the axial velocity, radial velocity, tangential velocity and temperature are increased when increasing the value of volume concentration \(\phi_{1}\). Figures 18 and 19 represent the axial and radial velocity profiles increase when increasing the value of volume concentration \(\phi_{2}\). Figures 14, 15, 16, 17, 18, 19) show, the effects of the solid volume fractions of Alumina/Aluminum oxide and Copper/Copper on the thermal field. The volume fraction of Alumina/Aluminium oxide and Cuprum/Copper are boosting the thermal phenomena. However, compared \(\phi_{1}\), the thermal profiles in the case of \(\phi_{2}\) are more obvious. Due to the nanoparticle volume fractions, the behaviour of these figures is consistent with the physical behaviour of the nanofluid. The thermal conductivity of the nanoparticles is greater than that of the base fluid, which increases the total thermal conductivity of the nanofluid and contributes to the rise in boundary layer temperature. Figure 20 illustrate the temperature profile with the variation of the Prandtl number. The temperature profile is decreased as well as we increase the value of the Prandtl number. This is because the thermal diffusivity of the fluid decreases due to higher values of Pr which further led to the reduction in the thermal boundary layer thickness.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(\phi_{1}\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{2}\) = 0.7, \(\beta_{3}\) = 0.6, \(\beta\) = 0.3, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.8, u = 0.5, \(\xi\) = 2.5.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(\phi_{1}\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{2}\) = 0.7, \(\beta_{3}\) = 0.6, \(\beta\) = 0.3, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.8, u = 0.5, \(\xi\) = 2.5.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of \(\phi_{1}\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{2}\) = 0.7, \(\beta_{3}\) = 0.6, \(\beta\) = 0.3, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.8, u = 0.5, \(\xi\) = 2.5.

Representation of tangential velocity \(g\left( \eta \right)\) for the different values of \(\phi_{1}\) with R = 3, n = 3, v = 0.8, \(m\) = 3.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{2}\) = 0.7, \(\beta_{3}\) = 0.6, \(\beta\) = 0.3, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.8, u = 0.5, \(\xi\) = 2.5.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(\phi_{2}\) with R = 7, n = 3, v = 0.2, \(m\) = 1.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{1}\) = 0.2, \(\beta_{3}\) = 0.9, \(\beta\) = 0.4, \(\beta_{1}\) = 0.2, \(\beta_{2}\) = 0.5, u = 0.3, \(\xi\) = 0.2.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(\phi_{2}\) with R = 7, n = 3, v = 0.2, \(m\) = 1.5, Pr = 0.9, \(\phi\) = 0.1, \(\phi_{1}\) = 0.2, \(\beta_{3}\) = 0.9, \(\beta\) = 0.4, \(\beta_{1}\) = 0.2, \(\beta_{2}\) = 0.5, u = 0.3, \(\xi\) = 0.2.

Representation of temperature \(\theta \left( \eta \right)\) for the different values of Pr with R = 3, n = 3, v = 0.7, \(m\) = 1.5, \(\phi_{2}\) = 0.8, \(\phi\) = 0.3, \(\phi_{1}\) = 0.1, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Figures 21 and 22 depict the behavior of axial and radial velocity for different values of the radiative parameter \(R\). The axial and radial velocity increased when the value of the radiative parameter \(R\) are raised. More heat is introduced to the thermal phenomena as a result of changing the radiation parameter. More heat is introduced to the thermal phenomena as a result of changing the radiation parameter. As a result, the temperature curves are increased by the increasing radiation parameter value. Physically, by raising the value of the parameter R, we may enhance the radiative heat transfer.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(R\) with R = 3, n = 3, v = 0.7, \(m\) = 1.5, \(\phi_{2}\) = 0.8, \(\phi\) = 0.3, \(\phi_{1}\) = 0.1, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(R\) with R = 3, n = 3, v = 0.7, \(m\) = 1.5, \(\phi_{2}\) = 0.8, \(\phi\) = 0.3, \(\phi_{1}\) = 0.1, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, u = 0.2, \(\xi\) = 0.2.

Figures 23 and 24 represent the distributions of axial and radial velocity for different values of dimensionless magnetic field intensity \(\left( \xi \right)\). When the value of the dimensionless magnetic field is increased, the axial and radial velocity distributions are reduced. As greater resistance to the flow phenomena is created by the application of the magnetic field, the velocity field also decreases. Therefore, a decrease in the velocity curves \(f\left( \eta \right)\) and \(f^{\prime}\left( \eta \right)\) is observed as a result of an improvement in the magnetic field intensity \(\left( \xi \right)\). The various axial and radial velocity profiles all meet their respective boundary criteria.

Representation of axial velocity \(f\left( \eta \right)\) for the different values of \(\xi\) with R = 3, n = 3, u = 0.2, \(m\) = 2.5, \(\phi_{2}\) = 0.8, \(\phi\) = 0.3, \(\phi_{1}\) = 0.1, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, Pr = 0.6, \(v\) = 0.1.

Representation of radial velocity \(f^{\prime}\left( \eta \right)\) for the different values of \(\xi\) with R = 3, n = 3, u = 0.2, \(m\) = 2.5, \(\phi_{2}\) = 0.8, \(\phi\) = 0.3, \(\phi_{1}\) = 0.1, \(\beta_{3}\) = 0.5, \(\beta\) = 0.4, \(\beta_{1}\) = 0.5, \(\beta_{2}\) = 0.9, Pr = 0.6, \(v\) = 0.1.

In Table 2 for distinct values of volume concentration \(\left( {\phi ,\phi_{1} ,\phi_{2} } \right)\), the heat transfer increases. Whereas ferromagnetic interaction numbers \(\left( {\beta ,\beta_{1} ,\beta_{2} ,\beta_{3} } \right)\) is the opposite. The heat transfer increases as dimensionless magnetic field intensity \(\xi\) is increased. The heat transmission in the fluid is reduced as the Prandtl number is increased. Table 3. demonstrate that the findings are in perfect accord with the results of the literature (Turkyilmazoglu77, Hafeez et al.49).

In this work, the flow and heat transport across a spinning disc under the influence of a nonlinearly extended alternating magnetic field in a radial direction are investigated. For the equations to be self-similar, stretching velocities may be obtained through lie group analysis in two ways: linear and power-law. The governing partial differential equations are turned into a system of coupled ordinary nonlinear differential equations with suitable similarity transformations. The following are the key conclusions from the study:

When an alternating magnetic field is present, additional flow resistance is formed by the volume concentration and the dimensionless magnetic field intensity. The heat transmission in the fluid is enhanced by rotational viscosity when the magnetic field is stationary, i.e., \(\omega_{0} \tau_{B} = 0\). The heat transmission in an alternating magnetic field is determined by the frequency of the field.

The ferromagnetic interaction numbers are noteworthy in defining the thickness of the momentum and thermal boundary layers. The heat transmission in the fluid is reduced as the Prandtl number is increased.

The existence of a fixed magnetic field increases the flow resistance to the maximum. When the dimensionless field frequency is unity, the magnetic field does not affect viscosity. The rotational viscosity of ferromagnetic fluid becomes negative when the dimensionless field frequency is larger than one.

It has been found that hybrid nanofluid flow outperforms nanofluid flow in terms of Nusselt number or heat transfer rate.

In future, similar work can be performed for flow over a surface and in the cylinderical domain.

Density \({\text{Kg}}/{\text{m}}^{3}\)

Velocity \({\text{m}}/{\text{s}}\)

Pressure \({\text{Kgm}}^{ - 1} {\text{s}}^{ - 2}\)

Reference viscosity \({\text{Pa}}.{\text{s}}\)

Magnetization

Magnetic field intensity \({\text{W}}/{\text{m}}^{2}\)

Rotational relaxation time

Angular velocity \({\text{m}}/{\text{s}}\)

Dissipation function

Volume fraction

Tangential axes

Radial direction

Axial direction

Prandtl number \({\text{m}}^{2} /{\text{s}}\)

Ambient temperature \(({\text{K}})\)

Radial stretching of disk

Density of solid \({\text{Kg}}/{\text{m}}^{3}\)

Heat capacitance of nanofluid \({\text{J}}/{\text{K}}\)

Vorticity

Brownian relaxation time

Instantaneous equilibrium magnetization

The moment of inertia \({\text{Kg}}.{\text{m}}^{2}\)

Time \({\text{s}}\)

Specific heat \({\text{J}}.{\text{Kg}}^{ - 1} .{\text{K}}^{ - 1}\)

Temperature \({\text{K}}\)

Thermal conductivity \({\text{Wm}}^{ - 1} {\text{K}}^{ - 1}\)

Magnetic induction \({\text{T}}\)

Strength of the magnetic field \({\text{T}}\)

Radial axes

Tangential direction

Reynolds number

Wall temperature \({\text{K}}\)

Uniform angular velocity \({\text{m}}/{\text{s}}\)

Density of fluid \({\text{Kg}}/{\text{m}}^{3}\)

Viscosity of fluid \({\text{Pa}}.{\text{s}}\)

Effective thermal conductivity \({\text{Wm}}^{ - 1} {\text{K}}^{ - 1}\)

Von Kármán, Th. Uber laminare und turbulente Reibung. Z. Angew. Math. Mech. 1, 233–252 (1921).

Article MATH Google Scholar

Cochrn, W. G. The flow due to a rotating disc. In Mathematical proceedings of the Cambridge philosophical society 365–3751 (Cambridge University Press, Cambridge, 2011).

Google Scholar

Millsaps, K. & Pohlhausen, K. Heat transfer by laminar flow from a rotating plate. J. Aeronaut. Sci. 19(2), 120–126 (1952).

Article MathSciNet MATH Google Scholar

Awad, M. M. Heat transfer from a rotating disk to fluids for a wide range of Prandtl numbers using the asymptotic model. J. Heat Transf. 130(1), 014505 (2008).

Article Google Scholar

Tadmor, Z. & Klein, I. Engineering Principles of Plasticating Extrusion (Van Nostrand Reinhold Company, New York, 1970).

Google Scholar

Asghar, S., Jalil, M., Hussan, M. & Turkyilmazoglu, M. Lie group analysis of flow and heat transfer over a stretching rotating disk. Int. J. Heat Mass Transf. 69, 140–146 (2014).

Article Google Scholar

Altan, T., Oh, S. I. & Gegel, G. Metal forming fundamentals and applications. Am. Soc. Met. 1983, 353 (1983).

Google Scholar

Crane, L. J. Flow past a stretching plate. Z. Angew. Math. Phys. ZAMP 21(4), 645–647 (1970).

Article Google Scholar

Wang, C. Y. The three-dimensional flow due to a stretching flat surface. Phys. Fluids 27(8), 1915–1917 (1984).

Article ADS MathSciNet MATH Google Scholar

Rashidi, M. M. & Mohimanian Pour, S. A. Analytic approximate solutions for unsteady boundary-layer flow and heat transfer due to a stretching sheet by homotopy analysis method. Nonlinear Anal. Modell. Control 15(1), 83–95 (2010).

Article MathSciNet MATH Google Scholar

Fang, T. Flow over a stretchable disk. Phys. Fluids 19(12), 128105 (2007).

Article ADS MATH Google Scholar

Fang, T. & Zhang, Ji. Flow between two stretchable disks—An exact solution of the Navier-Stokes equations. Int. Commun. Heat Mass Transf. 35(8), 892–895 (2008).

Article CAS Google Scholar

Turkyilmazoglu, M. MHD fluid flow and heat transfer due to a shrinking rotating disk. Comput. Fluids 90, 51–56 (2014).

Article MathSciNet MATH Google Scholar

Gupta, P. S. & Gupta, A. S. Heat and mass transfer on a stretching sheet with suction or blowing. Can. J. Chem. Eng. 55(6), 744–746 (1977).

Article Google Scholar

Sarafraz, M. M. et al. Pool boiling heat transfer characteristics of iron oxide nanosuspension under constant magnetic field. Int. J. Therm. Sci. 147, 106131 (2020).

Article CAS Google Scholar

Salari, E. et al. Thermal behavior of aqueous iron oxide nano-fluid as a coolant on a flat disc heater under the Pool boiling condition. Heat Mass Transf. 53, 265–275 (2017).

Article ADS CAS Google Scholar

Sarafraz, M. M., Hormozi, F. & Kamalgharibi, M. Sedimentation and convective boiling heat transfer of CuO-water/ethylene glycol nanofluids. Heat Mass Transf. 50, 1237–1249 (2014).

Article ADS CAS Google Scholar

Sarafraz, M. M. & Arjomandi, M. Thermal performance analysis of a microchannel heat sink cooling with copper oxide-indium (CuO/in) nano-suspensions at high-temperatures. Appl. Therm. Eng. 137, 700–709 (2018).

Article CAS Google Scholar

Sarafraz, M. M. et al. Flow boiling heat transfer to MgO-therminol 66 heat transfer fluid: experimental assessment and correlation development. Appl. Therm. Eng. 138, 552–562 (2018).

Article CAS Google Scholar

Salari, E. et al. Boiling thermal performance of TiO2 aqueous nanofluids as a coolant on a disc copper block. Period Polytech. Chem. Eng. 60, 106–122 (2015).

Google Scholar

Sarafraz, M. M. & Hormozi, F. Experimental investigation on the Pool boiling heat transfer to aqueous multiwalled carbon nanotube nanofluids on the micro-finned surfaces. Int. J. Therm. Sci. 100, 255–266 (2016).

Article CAS Google Scholar

Shahsavar, A. et al. Exergy studies in water-based and nanofluid-based photovoltaic/thermal collectors: Status and prospects. Renew. Sustain. Energy Rev. 168, 112740 (2022).

Article CAS Google Scholar

Shahsavar, A. et al. Experimental exploration of rheological behavior of polyethylene glycol-carbon dot nanofluid: Introducing a robust artificial intelligence paradigm optimized with unscented Kalman filter technique. J. Mol. Liquids 358, 119198 (2022).

Article CAS Google Scholar

Benton, E. R. On the flow due to a rotating disk. J. Fluid Mech. 24, 781–800 (1966).

Article ADS MATH Google Scholar

Attia, H. A. Unsteady MHD flow near a rotating porous disk with uniform suction or injection. Fluid Dyn. Res. 23, 283–290 (1998).

Article ADS Google Scholar

Attia, H. A. On the effectivness of ion slip and uniform suction or injection on steady MHD flow due to rotating disk with heat transfer ohmic heating. Chem. Eng. Commun. 194, 1396–1407 (2007).

Article CAS Google Scholar

Sibanda, P. & Makinde, O. D. On steady MHD flow and heat transfer past a rotating disk in a porous medium with ohmic heating and viscous dissipation. Int. J. Numer Methods Heat Fluid Flow 20, 269–285 (2010).

Article CAS Google Scholar

Ram, P., Bhandari, A. & Sharma, K. Effect of magnetic field-dependent viscosity on revolving ferrofluid. J. Magn. Magn. Mater. 322, 3476–3480 (2010).

Article ADS CAS Google Scholar

Bhandari, A. Study of ferrofluid flow in a rotating system through mathematical modeling. Math. Comput. Simul. 178, 290–306 (2020).

Article MathSciNet MATH Google Scholar

Bhandari, A. Effect of magnetic field dependent viscosity on the unsteady ferrofluid flow due to a rotating disk. Int. J. Appl. Mech. Eng. 25, 22–39 (2020).

Article CAS Google Scholar

Sarafraz, M. M. & Safaei, M. R. Diurnal thermal evaluation of an evacuated tube solar collector (ETSC) charged with graphene nanoplatelets-methanol nanosuspension. Renew. Energy 142, 364–372 (2019).

Article CAS Google Scholar

Rosensweig, R. E., Kaiser, R. & Miskolczy, G. Viscosity of magnetic fluid in a magnetic field. J. Colloid Interface Sci. 29, 680–686 (1969).

Article ADS CAS Google Scholar

Odenbach, S. & Thurm, S. Magnetoviscous effects in ferrofluids. In Ferrofluids 185–201 (Springer, Berlin, Heidelberg, 2002).

Chapter MATH Google Scholar

Rosensweig, R. E. Ferrohydrodynamics (Cambridge University Press, Cambridge, 1985).

Google Scholar

Odenbach, S. Ferrofluids: magnetically controllable liquids. PAMM 1, 28–32 (2002).

3.0.CO;2-8" data-track-action="article reference" href="https://doi.org/10.1002%2F1617-7061%28200203%291%3A1%3C28%3A%3AAID-PAMM28%3E3.0.CO%3B2-8" aria-label="Article reference 35" data-doi="10.1002/1617-7061(200203)1:13.0.CO;2-8">Article MATH Google Scholar

Shliomis, M. I. & Morozov, K. I. Negative viscosity of ferrofluid under alternating magnetic field. Phys. Fluids 6, 2855–2861 (1994).

Article ADS CAS MATH Google Scholar

Bacri, J. C. et al. Negative viscosity effect in a magnetic fluid. Phys. Rev. Lett. 75, 2128–2131 (1995).

Article ADS CAS PubMed Google Scholar

Ram, P. & Bhandari, A. Effect of phase difference between highly oscillating magnetic field and magnetization on the unsteady ferrofluid flow due to a rotating disk. Res. Phys. 3, 55–60 (2013).

Google Scholar

Ram, P. & Bhandari, A. Negative viscosity effects on ferrofluid flow due to a rotating disk. JAE 41, 467–478 (2013).

Article Google Scholar

Pourmehran, O., Sarafraz, M. M., Rahimi-Gorji, M. & Ganji, D. D. Rheological behaviour of various metal-based nano-fluids between rotating discs: A new insight. J. Taiwan Inst. Chem. Eng. 88, 37–48 (2018).

Article CAS Google Scholar

Bhandari, A. & Kumar, V. Effect of magnetization force on ferrofluid flow due to a rotating disk in the presence of an external magnetic field. Eur. Phys. J. Plus 130(4), 1–12 (2015).

Article CAS Google Scholar

Shah, Z. et al. Influence of Cattaneo-Christov model on Darcy-Forchheimer flow of micropolar ferrofluid over a stretching/shrinking sheet. Int. Commun. Heat Mass Transf. 110, 104385 (2020).

Article CAS Google Scholar

Ghorbani, B., Ebrahimi, S. & Vijayaraghavan, K. CFD modeling and sensitivity analysis of heat transfer enhancement of a ferrofluid flow in the presence of a magnetic field. Int. J. Heat Mass Transf. 127, 544–552 (2018).

Article CAS Google Scholar

Bezaatpour, M. & Goharkhah, M. Effect of magnetic field on the hydrodynamic and heat transfer of magnetite ferrofluid flow in a porous fin heat sink. J. Magn. Magn. Mater. 476, 506–515 (2019).

Article ADS CAS Google Scholar

Bhandari, A. Study of magnetoviscous effects on ferrofluid flow. Eur. Phys. J. Plus 135, 1–14 (2020).

Article Google Scholar

Ahmed, J., Khan, M. & Ahmad, L. Radiative heat flux effect in flow of maxwell nanofluid over a spiraling disk with chemically reaction. Phys. A Stat. Mech. Appl. 551, 123948 (2020).

Article MathSciNet CAS MATH Google Scholar

Khan, M., Ahmed, J. & Rasheed, Z. Entropy generation analysis for axisymmetric flow of Carreau nanofluid over a radially stretching disk. Appl. Nanosci. https://doi.org/10.1007/s13204-020-01399-7 (2020).

Article Google Scholar

Khan, M. et al. Non-axisymmetric homann MHD stagnation point flow of Al2O3-Cu/water hybrid nanofluid with shape factor impact. Appl. Math. Mech 41, 1125–1138 (2020).

Article Google Scholar

Hafeez, A. et al. Rotational flow of Oldroyd-B nanofluid subject to Cattaneo-Christov double diffusion theory. Appl. Math. Mech.Engl. Ed. 41, 1083–1094 (2020).

Article MathSciNet MATH Google Scholar

Khan, M., Ali, W. & Ahmed, J. A hybrid approach to study the influence of hall current in radiative nanofluid flow over a rotating disk. Appl. Nanosci. https://doi.org/10.1007/s13204-020-01415-w (2020).

Article Google Scholar

Sarafraz, M. M. et al. Thermal performance and viscosity of biologically produced silver/ coconut oil nanofluids. Chem. Biochem. Eng. Q. 30, 489–500 (2017).

Article Google Scholar

Bhandari, A., Pavan, R. K. & Pannala, K. Optimization of heat transfer properties of nanofluid flow over a shrinking surface through mathematical modeling. Int. J. Appl. Mech. Eng. 25, 40–56 (2020).

Article Google Scholar

Khan, M. et al. Non-axisymmetric Homann stagnation-point flow of Walter's B nanofluid over a cylindrical disk. Appl. Math. Mech. Engl. Ed. 41, 725–740 (2020).

Article MathSciNet MATH Google Scholar

Bhandari, A. & Husain, A. Optimization of heat transfer properties on ferrofluid flow over a stretching sheet in the presence of static magnetic field. J. Therm. Anal. Calorim. https://doi.org/10.1007/s10973-020-09636-5 (2020).

Article Google Scholar

Ahmed, J., Khan, M. & Ahmad, L. MHD von Ka´rma’n swirling flow in the Maxwell nanofluid with nonlinear radiative heat flux and chemical reaction. Heat Trans. Res. 51, 377–394 (2020).

Article Google Scholar

Iqbal, K. et al. Magnetohydrodynamic thin film deposition of Carreau nanofluid over an unsteady stretching surface. Appl. Phys. A 126, 105 (2020).

Article ADS CAS Google Scholar

Olver, P. Application of Lie groups to differential equations, Graduate Texts in Mathematics Vol. 107 (Springer, Cham, 1986).

Book Google Scholar

Azizian, R. et al. Effect of magnetic field on laminar convective heat transfer of magnetite nanofluids. Int. J. Heat Mass Transf. 68, 94–109 (2014).

Article Google Scholar

Goharkhah, M., Salarian, A., Ashjaee, M. & Shahabadi, M. Convective heat transfer characteristics of magnetite nanofluid under the influence of constant and alternating magnetic field. Powder Technol. 274, 258–267 (2015).

Article CAS Google Scholar

Sheikholeslami, M. & Ganji, D. D. Ferrohydrodynamic and magnetohydrodynamic effects on ferrofluid flow and convective heat transfer. Energy 75, 400–410 (2014).

Article CAS Google Scholar

Miroshnichenko, I. V., Sheremet, M. A., Pop, I. & Ishak, A. Convective heat transfer of micropolar fluid in a horizontal wavy channel under the local heating. Int. J. Mech. Sci. 128, 541–549 (2017).

Article Google Scholar

Dogonchi, A. S. et al. Thermal and entropy analyses on buoyancy-driven flow of nanofluid inside a porous enclosure with two square cylinders: Finite element method. Case Stud. Therm. Eng. 27, 101298 (2021).

Article Google Scholar

Eshaghi, S. et al. The optimum double diffusive natural convection heat transfer in H-Shaped cavity with a baffle inside and a corrugated wall. Case Stud. Therm. Eng. 28, 101541 (2021).

Article Google Scholar

Chamkha, A. J., Dogonchi, A. S. & Ganji, D. D. Magnetohydrodynamic nanofluid natural convection in a cavity under thermal radiation and shape factor of nanoparticles impacts: A numerical study using CVFEM. Appl. Sci. 8(12), 2396 (2018).

Article CAS Google Scholar

Dogonchi, A. S. et al. Investigation of magneto-hydrodynamic fluid squeezed between two parallel disks by considering Joule heating, thermal radiation, and adding different nanoparticles. Int. J. Numer. Methods Heat Fluid Flow 30(2), 659–680 (2019).

Article Google Scholar

Ghasemian, M., Ashrafi, Z. N., Goharkhah, M. & Ashjaee, M. Heat transfer characteristics of Fe3O4 ferrofluid flowing in a mini channel under constant and alternating magnetic fields. J. Magn. Magn. Mater. 381, 158–167 (2015).

Article ADS CAS Google Scholar

Bluman, G. W. & Kumei, S. Symmetries and differential equations. In Applied Mathematical Sciences Vol. 1 (Springer, Berlin, New York, 1989).

Google Scholar

Ibragimov, N. K. CRC Handbook of Lie Group Analysis of Differential Equations, Symmetries, Exact Solutions, and Conservation Laws Vol. I (CRC Press LLC, New York, 1994).

MATH Google Scholar

Jalil, M., Asghar, S. & Mushtaq, M. Lie group analysis of mixed convection flow with mass transfer over a stretching surface with suction or injection. Math. Prob. Eng. https://doi.org/10.1155/2010/264901 (2010).

Article MathSciNet MATH Google Scholar

Jalil, M. & Asghar, S. Flow of power-law fluid over a stretching surface: A lie group analysis. Int. J. Non-Linear Mech. 48, 65–71 (2013).

Article ADS Google Scholar

Jalil, M., Asghar, S. & Imran, S. M. Self-similar solutions for the flow and heat transfer of Powell-Eyring fluid over a moving surface in a parallel free stream. Int. J. Heat Mass Transf. 65, 73–79 (2013).

Article Google Scholar

Hamad, M., Uddin, M. J. & Ismail, A. Investigation of combined heat and mass transfer by lie group analysis with variable diffusivity taking into account hydrodynamic slip and thermal convective boundary conditions. Int. J. Heat Mass Transf. 55(4), 1355–1362 (2012).

Article MATH Google Scholar

Ferdows, M., Uddin, M. J., Rashidi, M. M. & Rahimzadeh, N. Numerical analysis of mixed convection over horizontal moving porous flat plate by the method of one parameter continuous group theory. Int. J. Number Methods Heat Fluid Flow 23(5), 729–749 (2013).

Article MathSciNet MATH Google Scholar

Ferdows, M., Uddin, M.J. & Afify, A. Scaling group transformation for MHD boundary layer free convective heat and mass transfer flow past a convectively heated nonlinear radiating stretching sheet. Int. J. Heat Mass Transf. 56(1–2), 181–187 (2013).

Article Google Scholar

Bhandari, A. Water-based ferrofluid flow and heat transfer over a stretchable rotating disk under the influence of an alternating magnetic field. Proc. Inst. Mech. Eng. C J. Mech. Eng. Sci. 235(12), 2201–2214 (2021).

Article CAS Google Scholar

Rauf, A., & Mushtaq, T. Cattaneo–Christov-based study of AL2O3–Cu/EG Casson hybrid nanofluid flow past a lubricated surface with cross diffusion and thermal radiation. Appl. Nanosci. 12, 1–18 (2022).

Article Google Scholar

Turkyilmazoglu, M. Nanofluid flow and heat transfer due to a rotating disk. Comput. Fluids 94, 139–146 (2014).

Article MathSciNet CAS MATH Google Scholar

Download references

These authors contributed equally: Abdul Rauf and Nehad Ali Shah.

Department of Mathematics, Air University Multan Campus, Chak 5-Faiz, Bahawalpur Road, Multan, Pakistan

Abdul Rauf & Aqsa Mushtaq

Department of Mechanical Engineering, Sejong University, Seoul, 05006, South Korea

Nehad Ali Shah

Department of Mathematics, Faculty of Science, Khon Kaen University, Khon Kaen, 40002, Thailand

Thongchai Botmart

You can also search for this author in PubMed Google Scholar

All authors contributed to the manuscript.

Correspondence to Thongchai Botmart.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Rauf, A., Mushtaq, A., Shah, N.A. et al. Heat transfer and hybrid ferrofluid flow over a nonlinearly stretchable rotating disk under the influence of an alternating magnetic field. Sci Rep 12, 17548 (2022). https://doi.org/10.1038/s41598-022-21784-2

Download citation

Received: 08 June 2022

Accepted: 04 October 2022

Published: 20 October 2022

DOI: https://doi.org/10.1038/s41598-022-21784-2

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

Scientific Reports (2023)

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.